Home»Garden»Irrigation

Last Updated on August 10 , 2023

project out the skilful way to water plant can be one of the most thought-provoking parts of gardening . get ’s fix that today ! Come along and learn how to colligate drip irrigation to a hose bibb ( spigot or spigot ) to create aneasy and efficientsystem to water your plants . This round-eyed DIY drip irrigation system can be used to bring home the bacon water to a mixture of garden areas such as flower beds , woodlet , raise garden bed , or even a patio container garden .

A hose end timer is connected to a faucet along a bark mulched border that is running along a fence line.

Even better , I will show you how toautomatethe arrangement . You wo n’t even have to think about watering once it ’s installed ! As far as “ installation ” pass , do not be intimidated . Zero plumbing skills are required to get in touch drip mold irrigation to a hosiery bibb , I promise .

2023 Update : We now have a tutorial on how to connect an loose drip irrigation organisation toraised garden bedsfrom a spigot or spigot!Check it out here . Or , if you want to water prove bed using drip tapeline , see howhere .

Would you like to save this?

We ’ll email this post to you , so you may come back to it later !

I consort to receive email update .

Disclosure : Homestead and Chill is reader - supported . When you buy through link on our web site , we may realize an affiliate charge .

A two part image collage showing the area of the property that will be converted to a drip irrigation hose bibb set up. The first image shows a fenced corner of the property with brown grass and weeds with a background of oak trees. The second image shows the area along the fence line to have been mulched with bark about 3 feet out from the fencing with trees, shrubs, and plants planted in a line along the two sides of the fence. Large oak trees make up the background amongst brown grasses.

Supplies Needed to Connect Drip Irrigation to a Hose Bibb or Faucet

A note about ½” irrigation tubing options and pressure

I should remark that it ’s industry “ best drill ” to not surpassover 100 feetof received solid irrigation tube as the organization may embark on tolose pressureat the end of longer runs . However , we ’ve true run irrigation tubing much farther … maybe up to 250 feet . The far end did have slightly less pressure than the first , but it still did the line of work ! you’re able to also supply gamy flow ( GPH ) emitter towards the end to compensate if want . For very large expanse ( where more than 200 - 300 feet of line is needed ) , it ’s respectable to split up the system into separate line that will run at unlike time if potential – like we ’re doing via our 2 - outlet hose timer .

Also note that there are different types of ½ ” drip tubing useable , such as“pressure compensating ” tubing . It has pre - installed emitter in the railway line every so often , such as every 9 inches , 12 inches , 18 inch , and so on . That character of irrigation tube can wield even insistency in much prospicient distances than received tubing . Yet it define how much you’re able to customize the system and piss output .

Optional Supplies

Now that we ’ve go over all the supplying call for to connect drip irrigation to a hose bibb or spigot , let ’s see how to set it all up !

Connecting a Drip Irrigation System to a Hose Bibb (Demonstration Video)

How to Attach a Drip Irrigation System to a Hose Bibb or Spigot (Written Summary)

Step 1: Add a Drip Adapter to the Hose Bib

start by deciding exactly how you ’d like to connect your drip irrigation to the hosepipe bibb or spigot . Feel free to follow one of theconfigurationexamples shown below . For instance , if you ’d like to include a Y - valve or hosepipe timekeeper . The most introductory installing is to connect the faucet adapter right to your hosiery bibb , where you ’d manually work the faucet on or off to melt the dripping arrangement . Attach the ½ ” irrigation tubing ( supply line ) to the adapter by steadfastly pressing it into the barbed outlet . ( Some adapters may have a hump - down clinch connexion or else ) .

Though they ’re made to be outside , protecting your hosiery timer from directsun exposurecan serve prolong its life . Sun and heat energy make plastic brittle over time . Therefore , consider deal the timekeeper with an old cloth or bucket to shield it .

Step 2: Lay Out the Supply Line

Next , lie out the ½ ” irrigation tubing supply business to the area you desire to deliver water supply . It ’s best to keep the provision linecenteredin the landscaped area , orclose to the base of plants . Secure the provision line to the ground with landscape painting staples or hooked stake . We typically work ours down under the layer of bark mulch ( if present ) to veil the main melodic phrase , but expect to do this until after we ’ve installed all our drip mold emitters .

adjudicate where you want the trickle irrigation organisation to end . Use tart scissors hold to cut off the tubing . Beforecapping the endof your line , you may desire to turn on the water toflush it outand clear any debris first . ( specially if you distrust crap got into the end of the line while you were laying it out . ) Once cleared , use a material body 8 clinch to pinch and end the line . Or , pen up the last of the product line back over itself and secure it with sturdy tape .

Step 3: Add Drip Emitters

Now it is prison term to add together your drip emitter of choice . To add the drip emitter along the main irrigation supplying line , habituate apunch toolto make belittled holes in the tubing at the desire locations . Carefully support the tube as you practice the slug , being conservative to not push all the direction through both side of the thermionic valve . Insert thebarbed endof the drip emitter into the hollow and wrestle it into topographic point .

Alternatively , you’re able to supply water system to an areafurther awayfrom the master line via microtubing . Use aconnectorwith barbs on each end to attach¼ ” microtubingto the main supply short letter . Then trim down the microtubing to the desire length and add a dribble emitter to the opposite ending of the tubing . This is a great way to watercontainers or potsfrom a drip irrigation arrangement connect to a hosiery bibb . We ’ve also usedbubblersor micro - sprinklers to deliver more water ( and a prominent surface field ) to Sir Herbert Beerbohm Tree on the same drip irrigation organisation as other plant with lower water need .

Drip emitter options & irrigation frequency

Drip emitter fall in various flow rate , typically list ingallons per hour(GPH ) . What you choose to use will be based onyour unparalleled irrigation demand . For instance , your climate , the types of plants you ’re growing , and the length and oftenness you project to scat your drip strain .   It may take a little research to figure out how much water each plant life needs . Check out this straightaway and helpfulirrigation guidefrom University of Nebraska - Lincoln . Or , seethis more elaborated articleabout watering newly plant trees and bush from the University of Minnesota .

In this new landscape area , we installed 2 GPH emitter and start the system for one 60 minutes every 3 days ( for now ) . It is presently our warm season ( September - October ) , and we do not receive any rainwater here except in the winter month . We ’ll twist the system off or down once rainwater amount . Also , we ’ll in all probability lessen the duration and/or frequency once the industrial plant are more established . We put in one emitter per perennial bush ( verbena , salvia , pincushion , sweet bay laurel ) since they ’re all fairly drouth - kind . The edible shrubs and yield trees ( pineapple guava , mulberry tree , pomegranate tree , Meyer lemons ) all received two emitter – one on each side of their solution ball .

Ongoing maintenance

Check your irrigation system sporadically to guarantee everything is functioning properly . Is the soil moist where desire ? Do any plants seem accent – signaling they may need more or less water ? It ’s easy to alter your system by tote up additional dripping emitter , raise sure areas to higher - output drinking fountain , or to cut back pee by reducing the fourth dimension or frequency . If you ’re using an automatic timer , be certain to check thebatterieson function ! You could also consider upgrading to asolar - power hosepipe timer .

Now turn on your new DIY irrigation system and enjoy easy, efficient watering!

You may also delight these articles :

Items you may need for drip irrigation hose bibb setups. There is a piece of cardboard as a back drop with a automated hose timer, faucet adapter, hole punch, emitters, figure eight clamp, y-valve, staples, micro sprinklers, 1/4 inch drip tubing, 1/2 inch tubing, and barbed connectors.

Half inch drip tubing is running horizontally across the image, a T connecting piece has been used to attach another piece of drip tubing to run vertically, perpendicular to the main line.

A basic drip irrigation hose bibb set up with a 3 in 1 adapter connected to the bibb and half inch drip tubing connected to the other end.

A standard water spigot with a Y-valve attachment with a drip converter connecting the irrigation tubing to the system.

A drip irrigation hose bib set up with an automated timer connected to two 3 in 1 drip adapters that are connecting the drip tubing to the whole system.

A raised water spigot has a “Y” valve attached to it, connected to an automated timer with two 3 in 1 drip adapters that is connecting the drip tubing to the whole system.

A drip irrigation hose bibb set up along a fence line with shrubs, small trees, and pollinator plants are planted along the fence. Bark is mulching the area in a solid strip along the fence and around the plants with the drip tubing visible sitting on top of the mulch.

DeannaCat is holding the end of the irrigation tubing after it has been folded in half with a figure eight clamp on the end of it to stop the water from flowing out of the end.

A three part image collage, the first image shows a hand bracing one side of the half inch tubing while the other hand is using an irrigation punch to make a hole in the tubing. The second image shows a 2 gallon an hour emitter next to the hole in the tubing, the third image shows the emitter connected into the drip irrigation tubing from a hose bibb.

A three part image collage, the first image shows DeannaCat’s hand holding a part of the half inch irrigation tubing along with a connector barb, while also showing quarter inch tubing connected into the main drip line via an additional connector barb. The second image shows DeannaCat holding a drip emitter connected to quarter inch tubing and a micro sprinkler. The third image shows DeannaCat pulling quarter inch drip tubing with an emitter on the end towards a plant that is several feet away from the main drip line.

A close up of half inch black irrigation tubing running along bark mulch that is connected to drip irrigation hose bibb. Two drip emitters are dispensing water to a pineapple guava shrub.

DeannaCat signature, keep on growing